回答

收藏

[评测分享] 【飞凌RZG2L开发板测评】_forlinx_ok-g2lx_硬件测试

#板卡评测 #板卡评测 1385 人阅读 | 0 人回复 | 2022-10-17

forlinx_ok-g2lx
硬件测试
1. 测试准备工作
使用串口调试工具连接开发板的DEBUG调试接口,GND,RXD,TXD
波特率:115200
图一
l 调试串口显示开机信息
==============================================
U-Boot 2020.10 (May 23 2022 - 01:01:36 +0000)
CPU: Renesas Electronics E rev 10.2
Model: OKG2L-C
DRAM:  1.9 GiB
MMC:   sh-sdhi: 0, sh-sdhi: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment
In:    serial@1004b800
Out:   serial@1004b800
Err:   serial@1004b800
Net:   
Error: ethernet@11c20000 address not set.
No ethernet found.
Autoboot in 1 seconds
Card did not respond to voltage select!
15555072 bytes read in 691 ms (21.5 MiB/s)
30186 bytes read in 16 ms (1.8 MiB/s)
## Flattened Device Tree blob at 48000000
   Booting using the fdt blob at 0x48000000
   Loading Device Tree to 00000000bbf30000, end 00000000bbf3a5e9 ... OK
Starting kernel ...
[    0.141135] mtd: partition "test-area" is out of reach -- disabled
[    0.443117] ov5645 0-003c: ov5645_write_reg: write reg error -6: reg=3103, val=11
[    0.450594] ov5645 0-003c: could not set init registers
[    0.455810] ov5645 0-003c: could not power up OV5645
[    0.467778] rzg2l_wdt 12800800.watchdog: IRQ index 0 not found
[    0.562616] thermal emergency: not set value
Welcome to Poky (Yocto Project Reference Distro) 3.1.5 (dunfell)!
[  OK  ] Created slice system-getty.slice.
[  OK  ] Created slice system-serial\x2dgetty.slice.
[  OK  ] Created slice User and Session Slice.
[  OK  ] Started Dispatch Password …ts to Console Directory Watch.
[  OK  ] Started Forward Password R…uests to Wall Directory Watch.
[  OK  ] Reached target Paths.
[  OK  ] Reached target Remote File Systems.
[  OK  ] Reached target Slices.
[  OK  ] Reached target Swap.
[  OK  ] Listening on RPCbind Server Activation Socket.
[  OK  ] Reached target RPC Port Mapper.
[  OK  ] Listening on Syslog Socket.
[  OK  ] Listening on initctl Compatibility Named Pipe.
[  OK  ] Listening on Journal Audit Socket.
[  OK  ] Listening on Journal Socket (/dev/log).
[  OK  ] Listening on Journal Socket.
[  OK  ] Listening on Network Service Netlink Socket.
[  OK  ] Listening on udev Control Socket.
[  OK  ] Listening on udev Kernel Socket.
         Mounting Huge Pages File System...
         Mounting POSIX Message Queue File System...
         Mounting Kernel Debug File System...
         Mounting Temporary Directory (/tmp)...
         Starting Create list of st…odes for the current kernel...
[  OK  ] Started Hardware RNG Entropy Gatherer Daemon.
         Starting RPC Bind...
         Starting Journal Service...
         Starting Load Kernel Modules...
         Starting Remount Root and Kernel File Systems...
         Starting udev Coldplug all Devices...
[  OK  ] Started RPC Bind.
[    1.899261] mali 11840000.mali: Continuing without devfreq
[  OK  ] Mounted Huge Pages File System.
[  OK  ] Mounted POSIX Message Queue File System.
[  OK  ] Mounted Kernel Debug File System.
[  OK  ] Mounted Temporary Directory (/tmp).
[  OK  ] Started Create list of sta… nodes for the current kernel.
[  OK  ] Started Remount Root and Kernel File Systems.
         Starting Create Static Device Nodes in /dev...
[  OK  ] Started Create Static Device Nodes in /dev.
[  OK  ] Started Journal Service.
[  OK  ] Started Load Kernel Modules.
[  OK  ] Reached target Local File Systems (Pre).
         Mounting Kernel Configuration File System...
         Mounting /var/volatile...
         Starting Flush Journal to Persistent Storage...
         Starting Apply Kernel Variables...
         Starting udev Kernel Device Manager...
[  OK  ] Mounted Kernel Configuration File System.
[  OK  ] Mounted /var/volatile.
[  OK  ] Started Flush Journal to Persistent Storage.
[  OK  ] Started Apply Kernel Variables.
         Starting Load/Save Random Seed...
[  OK  ] Reached target Local File Systems.
         Starting Create Volatile Files and Directories...
[  OK  ] Started udev Kernel Device Manager.
[  OK  ] Started Create Volatile Files and Directories.
         Starting Network Time Synchronization...
         Starting Update UTMP about System Boot/Shutdown...
[  OK  ] Started Update UTMP about System Boot/Shutdown.
[  OK  ] Started Network Time Synchronization.
[  OK  ] Reached target System Time Set.
[  OK  ] Reached target System Time Synchronized.
[  OK  ] Started udev Coldplug all Devices.
[  OK  ] Reached target System Initialization.
[  OK  ] Started Daily Cleanup of Temporary Directories.
[  OK  ] Reached target Timers.
[  OK  ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.
[  OK  ] Listening on D-Bus System Message Bus Socket.
         Starting sshd.socket.
[  OK  ] Listening on sshd.socket.
[  OK  ] Reached target Sockets.
[  OK  ] Reached target Basic System.
[  OK  ] Started autorun.
[  OK  ] Started Kernel Logging Service.
[  OK  ] Started System Logging Service.
[  OK  ] Started D-Bus System Message Bus.
         Starting IPv6 Packet Filtering Framework...
         Starting IPv4 Packet Filtering Framework...
         Starting Lighttpd Daemon...
         Starting rng-tools.service...
         Starting Login Service...
[  OK  ] Started IPv6 Packet Filtering Framework.
[  OK  ] Started IPv4 Packet Filtering Framework.
[  OK  ] Started Lighttpd Daemon.
[  OK  ] Started rng-tools.service.
[  OK  ] Created slice system-systemd\x2dbacklight.slice.
[  OK  ] Reached target Network (Pre).
         Starting Load/Save Screen …ness of backlight:backlight...
         Starting Network Service...
         Starting weston.service...
[  OK  ] Started Load/Save Screen B…htness of backlight:backlight.
[  OK  ] Started weston.service.
[  OK  ] Started Load/Save Random Seed.
[  OK  ] Started matrix-browser.
[    4.079616] edt_ft5x06 1-0038: touchscreen probe failed
[  OK  ] Started Network Service.
         Starting Networ[    4.248566] Goodix-TS 1-0014: i2c test failed attempt 1: -6
k Name Resolution...
[  OK  ] Started Login Service.
[    4.329323] Goodix-TS 1-0014: i2c test failed attempt 2: -6
[    4.439528] Goodix-TS 1-0014: I2C communication failure: -6
[  OK  ] Started Network Name Resolution.
[  OK  ] Reached target Network.
[  OK  ] Reached target Host and Network Name Lookups.
         Starting Avahi mDNS/DNS-SD Stack...
[  OK  ] Started laohua.
         Starting Permit User Sessions...
[  OK  ] Started Vsftpd ftp daemon.
[  OK  ] Started Permit User Sessions.
[  OK  ] Started Avahi mDNS/DNS-SD Stack.
[  OK  ] Created slice system-weston.slice.
[  OK  ] Started Getty on tty1.
[  OK  ] Started Getty on tty2.
[  OK  ] Started Serial Getty on ttySC0.
[  OK  ] Reached target Login Prompts.
[  OK  ] Reached target Multi-User System.
         Starting Update UTMP about System Runlevel Changes...
[  OK  ] Started Weston Wayland Compositor.
[  OK  ] Started Update UTMP about System Runlevel Changes.
Poky (Yocto Project Reference Distro) 3.1.5 okg2l ttySC0
BSP: RZG2L/RZG2L-SMARC-EVK/1.3
LSI: RZG2L
Version: 1.3
okg2l login:
=========================================
开机速度很快
登录用户名:forlinx
密码:forlinx
由于普通用户权限有限,切换到root
用户名:root/密码:空
2. 操作系统版本
root@okg2l:~# cat /proc/version
Linux version 4.19.165-cip41-arm64-renesas (root@e84858de0f27) (gcc version 8.3.0 (GCC)) #1 SMP PREEMPT Mon Jun 13 02:34:03 UTC 2022
root@okg2l:~# uname -a
Linux okg2l 4.19.165-cip41-arm64-renesas #1 SMP PREEMPT Mon Jun 13 02:34:03 UTC 2022 aarch64 GNU/Linux
3. **配置状态
root@okg2l:/etc/systemd/network# ifconfig
can0: flags=128<NOARP>  mtu 72  metric 1
        unspec 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00  txqueuelen 10  (UNSPEC)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
can1: flags=128<NOARP>  mtu 72  metric 1
        unspec 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00  txqueuelen 10  (UNSPEC)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500  metric 1
        inet 192.168.1.1  netmask 255.255.255.0  broadcast 192.168.1.255
        ether 7a:b8:66:57:39:2b  txqueuelen 1000  (Ethernet)
        RX packets 12  bytes 1568 (1.5 KiB)
        RX errors 0  dropped 3  overruns 0  frame 0
        TX packets 74  bytes 5302 (5.1 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 118    dma 0xff
eth1: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500  metric 1
        inet 192.168.1.2  netmask 255.255.255.0  broadcast 192.168.1.255
        ether 7a:b8:66:57:39:2c  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 121    dma 0xff
lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536  metric 1
        inet 127.0.0.1  netmask 255.0.0.0
        loop  txqueuelen 1000  (Local Loopback)
        RX packets 239  bytes 347234 (339.0 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 239  bytes 347234 (339.0 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
usb0: flags=4226<BROADCAST,NOARP,MULTICAST>  mtu 1500  metric 1
        ether 62:b6:c9:0f:46:da  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
wlan0: flags=4098<BROADCAST,MULTICAST>  mtu 1500  metric 1
        ether 30:7b:c9:47:f8:da  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
wlan1: flags=4098<BROADCAST,MULTICAST>  mtu 1500  metric 1
        ether 32:7b:c9:47:f8:da  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
4. 路由表
root@okg2l:/etc/systemd/network# route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
0.0.0.0         192.168.110.1   0.0.0.0         UG    10     0        0 eth0
192.168.1.0     0.0.0.0         255.255.255.0   U     0      0        0 eth0
192.168.1.0     0.0.0.0         255.255.255.0   U     0      0        0 eth1
192.168.1.11    0.0.0.0         255.255.255.255 UH    0      0        0 eth0
192.168.1.22    0.0.0.0         255.255.255.255 UH    0      0        0 eth1
192.168.110.0   0.0.0.0         255.255.255.0   U     0      0        0 eth0
192.168.110.1   0.0.0.0         255.255.255.255 UH    10     0        0 eth0
5. 文件系统
Filesystem            Size  Used Avail Use% Mounted on
/dev/root              14G  665M   13G   5% /
devtmpfs              743M     0  743M   0% /dev
tmpfs                 935M     0  935M   0% /dev/shm
tmpfs                 935M  9.8M  926M   2% /run
tmpfs                 935M     0  935M   0% /sys/fs/cgroup
tmpfs                 935M  3.4M  932M   1% /tmp
tmpfs                 935M  108K  935M   1% /var/volatile
tmpfs                 187M     0  187M   0% /run/user/0
tmpfs                 187M     0  187M   0% /run/user/1000
6. 内存状态
root@okg2l:~# free -m
              total        used        free      shared  buff/cache   available
Mem:        1914528     1505708      277248       16624      131572      335864
Swap:             0           0           0
7. 4G模块状态
4G-EC20执行拨号上网脚本
root@okg2l:/# quectel-CM &   
root@okg2l:/# [09-07_15:51:59:757] Quectel_QConnectManager_Linux_V1.6.0.24
[09-07_15:51:59:776] Find /sys/bus/usb/devices/2-1.4 idVendor=0x2c7c idProduct=0x125, bus=0x002, dev=0x004
[09-07_15:51:59:781] Auto find qmichannel = /dev/qcqmi2
[09-07_15:51:59:782] Auto find usbnet_adapter = usb0
[09-07_15:51:59:783] netcard driver = GobiNet, driver version = 22-Aug-2005
[09-07_15:51:59:786] Modem works in QMI mode
[09-07_15:51:59:869] Get clientWDS = 7
[09-07_15:51:59:901] Get clientDMS = 8
[09-07_15:51:59:933] Get clientNAS = 9
[09-07_15:51:59:965] Get clientUIM = 10
[09-07_15:51:59:997] Get clientWDA = 11
[09-07_15:52:00:029] requestBaseBandVersion EC20CNHDLGR09A03M1G
[09-07_15:52:00:157] requestGetSIMStatus SIMStatus: SIM_READY
[09-07_15:52:00:189] requestGetProfile[1] ///0
[09-07_15:52:00:221] requestRegistrationState2 MCC: 0, MNC: 0, PS: Detached, DataCap: UNKNOW
[09-07_15:52:00:253] requestQueryDataCall IPv4ConnectionStatus: DISCONNECTED
[09-07_15:52:00:254] ifconfig usb0 0.0.0.0
[09-07_15:52:00:296] ifconfig usb0 down
[09-07_15:52:04:092] requestRegistrationState2 MCC: 0, MNC: 0, PS: Detached, DataCap: UNKNOW
[09-07_15:52:15:356] requestRegistrationState2 MCC: 460, MNC: 0, PS: Attached, DataCap: LTE
[09-07_15:52:15:772] requestSetupDataCall WdsConnectionIPv4Handle: 0x85d0b400
[09-07_15:52:15:900] requestRegistrationState2 MCC: 460, MNC: 0, PS: Attached, DataCap: LTE
[09-07_15:52:15:965] ifconfig usb0 up
[09-07_15:52:16:018] busybox udhcpc -f -n -q -t 5 -i usb0
udhcpc: started, v1.31.1
udhcpc: sending discover
udhcpc: sending select for 10.143.195.34
udhcpc: lease of 10.143.195.34 obtained, lease time 7200
[09-07_15:52:16:486] /etc/udhcpc.d/50default: Adding DNS 183.230.126.224
[09-07_15:52:16:487] /etc/udhcpc.d/50default: Adding DNS 183.230.126.225
生成usb0虚拟网卡
usb0: flags=4291<UP,BROADCAST,RUNNING,NOARP,MULTICAST>  mtu 1500  metric 1
        inet 10.177.186.112  netmask 255.255.255.224  broadcast 10.177.186.127
        ether 62:b6:c9:0f:46:da  txqueuelen 1000  (Ethernet)
        RX packets 4  bytes 1224 (1.1 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 25  bytes 2998 (2.9 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
8. Wifi模块状态
执行wifi连接脚本,输入wifi名称和密码(密码不能为空)
root@okg2l:/etc/init.d# fltest_wifi.sh  -i wlan0 -s ruijie_MCFI-187F55 -p 12345678
wifi wlan0
ssid ruijie_MCFI-187F55
pasw 12345678
wpa connect status:SCANNING
wpa connect status:ASSOCIATING
connect ok
udhcpc: started, v1.31.1
udhcpc: sending discover
udhcpc: sending discover
udhcpc: sending select for 192.168.110.135
udhcpc: lease of 192.168.110.135 obtained, lease time 28800
/etc/udhcpc.d/50default: Adding DNS 192.168.110.1
======================================================
root@okg2l:/#
root@okg2l:/# ifconfig
eth0: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500  metric 1
        inet 192.168.1.1  netmask 255.255.255.0  broadcast 192.168.1.255
        ether 7a:b8:66:57:39:2b  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 118    dma 0xff
eth1: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500  metric 1
        inet 192.168.1.2  netmask 255.255.255.0  broadcast 192.168.1.255
        ether 7a:b8:66:57:39:2c  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 121    dma 0xff
lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536  metric 1
        inet 127.0.0.1  netmask 255.0.0.0
        loop  txqueuelen 1000  (Local Loopback)
        RX packets 214  bytes 345310 (337.2 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 214  bytes 345310 (337.2 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
usb0: flags=4291<UP,BROADCAST,RUNNING,NOARP,MULTICAST>  mtu 1500  metric 1
        inet 10.143.195.34  netmask 255.255.255.252  broadcast 10.143.195.35
        ether 62:b6:c9:0f:46:da  txqueuelen 1000  (Ethernet)
        RX packets 2  bytes 612 (612.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 13  bytes 1583 (1.5 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

图一.jpg (61.51 KB, 下载次数: 35)

图一.jpg
分享到:
回复

使用道具 举报

您需要登录后才可以回帖 注册/登录

本版积分规则

关闭

站长推荐上一条 /3 下一条