登录/注册
与非网论坛 »首页 › 厂商小组 › NXP › 【米尔-NXP iMX9系列开发板试用评测】加载debian出错 ...

赞

回答

收藏

【米尔-NXP iMX9系列开发板试用评测】加载debian出错

NXP NXP 2869 人阅读 | 0 人回复 | 2024-06-18

我根据软件开发指南使用SD卡升级到emmc后启动报错。信息如下：

  2. U-Boot SPL 2023.04-g9bdc7571c0 (May 09 2024 - 16:27:05 +0800)
  3. SOC: 0xa1009300
  4. LC: 0x2040010
  5. PMIC: Over Drive Voltage Mode
  6. DDR: 3733MTS
  7. M33 prepare ok
  8. Normal Boot
  9. Trying to boot from BOOTROM
  10. Boot Stage: Primary boot
  11. image offset 0x0, pagesize 0x200, ivt offset 0x0
  12. Load image from 0x48000 by ROM_API
  13. NOTICE:  BL31: v2.8(release):lf-6.1.55-2.2.0-0-g08e9d4eef
  14. NOTICE:  BL31: Built : 06:43:30, Nov 21 2023


  17. U-Boot 2023.04-g9bdc7571c0 (May 09 2024 - 16:27:05 +0800)

  19. CPU:   i.MX93(52) rev1.1 1700 MHz (running at 1692 MHz)
  20. CPU:   Industrial temperature grade (-40C to 105C) at 45C
  21. Reset cause: POR (0x1)
  22. Model: NXP i.MX93 11X11 EVK board
  23. DRAM:  992 MiB
  24. tcpc_init: Can't find device id=0x52
  25. setup_typec: tcpc portpd init failed, err=-19
  26. tcpc_init: Can't find device id=0x51
  27. setup_typec: tcpc port2 init failed, err=-19
  28. tcpc_init: Can't find device id=0x50
  29. setup_typec: tcpc port1 init failed, err=-19
  30. Module INFO:
  31. >>>PN=MYD-LMX9352-8E1D-170-I
  32. >>>SN=WKRD23120100700026Y
  33. Not valid MAC address in eeprom!
  34. Core:  218 devices, 33 uclasses, devicetree: separate
  35. MMC:   FSL_SDHC: 0, FSL_SDHC: 1
  36. Loading Environment from MMC... OK
  37. [*]-Video Link 0fail to get display timings
  38. probe video device failed, ret -22

  40.         [0] lcd-controller@4ae30000, video
  41.         [1] dsi@4ae10000, video_bridge
  42. fail to get display timings
  43. probe video device failed, ret -22
  44. In:    serial
  45. Out:   serial
  46. Err:   serial

  48. BuildInfo:
  49.   - ELE firmware version 0.1.0-44880904

  51. myir board:MYD-LMX93Xswitch to partitions #0, OK
  52. mmc0(part 0) is current device
  53. flash target is MMC:0
  54. Net:   eth0: ethernet@42890000, eth1: ethernet@428a0000 [PRIME]
  55. Fastboot: Normal
  56. Normal Boot
  57. Hit any key to stop autoboot:  0
  58. switch to partitions #0, OK
  59. mmc0(part 0) is current device
  60. Scanning mmc 0:1...
  61. 46326 bytes read in 1 ms (44.2 MiB/s)
  62. Working FDT set to 83000000
  63. MMC: no card present
  64. No EFI system partition
  65. No EFI system partition
  66. Failed to persist EFI variables
  67. fail to get display timings
  68. BootOrder not defined
  69. EFI boot manager: Cannot load any image
  70. MMC: no card present
  71. starting USB...
  72. Bus usb@4c100000: Port not available.
  73. Bus usb@4c200000: Port not available.
  74. USB is stopped. Please issue 'usb start' first.
  75. Running BSP bootcmd ...
  76. switch to partitions #0, OK
  77. mmc0(part 0) is current device
  78. Failed to load 'boot.scr'
  79. 35052032 bytes read in 192 ms (174.1 MiB/s)
  80. Booting from mmc ...
  81. 46326 bytes read in 1 ms (44.2 MiB/s)
  82. ## Flattened Device Tree blob at 83000000
  83.    Booting using the fdt blob at 0x83000000
  84. Working FDT set to 83000000
  85.    Using Device Tree in place at 0000000083000000, end 000000008300e4f5
  86. Working FDT set to 83000000
  87. fail to get display timings
  88. probe video device failed, ret -22

  90. Starting kernel ...

  92. [    0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
  93. [    0.000000] Linux version 6.1.55+ga5c552ce6210 (oe-user@oe-host) (aarch64-poky-linux-gcc (GCC) 12.3.0, GNU ld (GNU Binutils) 2.40.0.20230703) #1 SMP PREEMPT Thu Apr 11 02:15:58 UTC 2024
  94. [    0.000000] Machine model: NXP i.MX93 11X11 EVK board
  95. [    0.000000] efi: UEFI not found.
  96. [    0.000000] Reserved memory: created CMA memory pool at 0x0000000086000000, size 256 MiB
  97. [    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
  98. [    0.000000] Reserved memory: created DMA memory pool at 0x00000000a4020000, size 1 MiB
  99. [    0.000000] OF: reserved mem: initialized node vdevbuffer@a4020000, compatible id shared-dma-pool
  100. [    0.000000] Reserved memory: created DMA memory pool at 0x00000000a4120000, size 1 MiB
  101. [    0.000000] OF: reserved mem: initialized node ele-reserved@a4120000, compatible id shared-dma-pool
  102. [    0.000000] Reserved memory: created CMA memory pool at 0x00000000b0000000, size 128 MiB
  103. [    0.000000] OF: reserved mem: initialized node ethosu_region@B0000000, compatible id shared-dma-pool
  104. [    0.000000] earlycon: lpuart32 at MMIO32 0x0000000044380000 (options '')
  105. [    0.000000] printk: bootconsole [lpuart32] enabled
  106. [    0.000000] NUMA: No NUMA configuration found
  107. [    0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000000bfffffff]
  108. [    0.000000] NUMA: NODE_DATA [mem 0xbfdd6700-0xbfdd8fff]
  109. [    0.000000] Zone ranges:
  110. [    0.000000]   DMA      [mem 0x0000000080000000-0x00000000bfffffff]
  111. [    0.000000]   DMA32    empty
  112. [    0.000000]   Normal   empty
  113. [    0.000000] Movable zone start for each node
  114. [    0.000000] Early memory node ranges
  115. [    0.000000]   node   0: [mem 0x0000000080000000-0x0000000095ffffff]
  116. [    0.000000]   node   0: [mem 0x0000000098000000-0x00000000a3ffffff]
  117. [    0.000000]   node   0: [mem 0x00000000a4000000-0x00000000a421ffff]
  118. [    0.000000]   node   0: [mem 0x00000000a4220000-0x00000000bfffffff]
  119. [    0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000bfffffff]
  120. [    0.000000] On node 0, zone DMA: 8192 pages in unavailable ranges
  121. [    0.000000] psci: probing for conduit method from DT.
  122. [    0.000000] psci: PSCIv1.1 detected in firmware.
  123. [    0.000000] psci: Using standard PSCI v0.2 function IDs
  124. [    0.000000] psci: Trusted OS migration not required
  125. [    0.000000] psci: SMC Calling Convention v1.2
  126. [    0.000000] percpu: Embedded 20 pages/cpu s44520 r8192 d29208 u81920
  127. [    0.000000] Detected VIPT I-cache on CPU0
  128. [    0.000000] CPU features: detected: GIC system register CPU interface
  129. [    0.000000] CPU features: detected: Virtualization Host Extensions
  130. [    0.000000] CPU features: detected: Qualcomm erratum 1009, or ARM erratum 1286807, 2441009
  131. [    0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
  132. [    0.000000] alternatives: applying boot alternatives
  133. [    0.000000] Fallback order for Node 0: 0
  134. [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 249856
  135. [    0.000000] Policy zone: DMA
  136. [    0.000000] Kernel command line: console=ttyLP0,115200 earlycon root=/dev/mmcblk0p3 rootwait rw
  137. [    0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
  138. [    0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
  139. [    0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off
  140. [    0.000000] Memory: 565136K/1015808K available (21056K kernel code, 1910K rwdata, 7676K rodata, 3456K init, 664K bss, 57456K reserved, 393216K cma-reserved)
  141. [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
  142. [    0.000000] rcu: Preemptible hierarchical RCU implementation.
  143. [    0.000000] rcu:     RCU event tracing is enabled.
  144. [    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2.
  145. [    0.000000]  Trampoline variant of Tasks RCU enabled.
  146. [    0.000000]  Tracing variant of Tasks RCU enabled.
  147. [    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
  148. [    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
  149. [    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
  150. [    0.000000] GICv3: GIC: Using split EOI/Deactivate mode
  151. [    0.000000] GICv3: 960 SPIs implemented
  152. [    0.000000] GICv3: 0 Extended SPIs implemented
  153. [    0.000000] Root IRQ handler: gic_handle_irq
  154. [    0.000000] GICv3: GICv3 features: 16 PPIs
  155. [    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000048040000
  156. [    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
  157. [    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
  158. [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
  159. [    0.000000] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
  160. [    0.008300] Console: colour dummy device 80x25
  161. [    0.012530] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
  162. [    0.022712] pid_max: default: 32768 minimum: 301
  163. [    0.027333] LSM: Security Framework initializing
  164. [    0.031955] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
  165. [    0.039266] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
  166. [    0.047730] cacheinfo: Unable to detect cache hierarchy for CPU 0
  167. [    0.053966] cblist_init_generic: Setting adjustable number of callback queues.
  168. [    0.060948] cblist_init_generic: Setting shift to 1 and lim to 1.
  169. [    0.067032] cblist_init_generic: Setting adjustable number of callback queues.
  170. [    0.074188] cblist_init_generic: Setting shift to 1 and lim to 1.
  171. [    0.080361] rcu: Hierarchical SRCU implementation.
  172. [    0.085022] rcu:     Max phase no-delay instances is 1000.
  173. [    0.091030] EFI services will not be available.
  174. [    0.095470] smp: Bringing up secondary CPUs ...
  175. [    0.100171] Detected VIPT I-cache on CPU1
  176. [    0.100232] cacheinfo: Unable to detect cache hierarchy for CPU 1
  177. [    0.100242] GICv3: CPU1: found redistributor 100 region 0:0x0000000048060000
  178. [    0.100275] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
  179. [    0.100365] smp: Brought up 1 node, 2 CPUs
  180. [    0.127788] SMP: Total of 2 processors activated.
  181. [    0.132458] CPU features: detected: 32-bit EL0 Support
  182. [    0.137580] CPU features: detected: 32-bit EL1 Support
  183. [    0.142685] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
  184. [    0.151261] CPU features: detected: Common not Private translations
  185. [    0.157500] CPU features: detected: CRC32 instructions
  186. [    0.162616] CPU features: detected: RCpc load-acquire (LDAPR)
  187. [    0.168333] CPU features: detected: LSE atomic instructions
  188. [    0.173881] CPU features: detected: Privileged Access Never
  189. [    0.179427] CPU features: detected: RAS Extension Support
  190. [    0.184804] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
  191. [    0.191784] CPU: All CPU(s) started at EL2
  192. [    0.195809] alternatives: applying system-wide alternatives
  193. [    0.205325] devtmpfs: initialized
  194. [    0.213071] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
  195. [    0.222570] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
  196. [    0.237496] pinctrl core: initialized pinctrl subsystem
  197. [    0.243748] DMI not present or invalid.
  198. [    0.247773] NET: Registered PF_NETLINK/PF_ROUTE protocol family
  199. [    0.254226] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
  200. [    0.261106] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
  201. [    0.268797] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
  202. [    0.276671] audit: initializing netlink subsys (disabled)
  203. [    0.282191] audit: type=2000 audit(0.188:1): state=initialized audit_enabled=0 res=1
  204. [    0.282586] thermal_sys: Registered thermal governor 'step_wise'
  205. [    0.289717] thermal_sys: Registered thermal governor 'power_allocator'
  206. [    0.295838] cpuidle: using governor menu
  207. [    0.306279] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
  208. [    0.312886] ASID allocator initialised with 65536 entries
  209. [    0.318827] Serial: AMBA PL011 UART driver
  210. [    0.322709] imx mu driver is registered.
  211. [    0.326564] imx rpmsg driver is registered.
  212. [    0.336135] imx93-pinctrl 443c0000.pinctrl: initialized IMX pinctrl driver
  213. [    0.348475] platform 4ae30000.lcd-controller: Fixed dependency cycle(s) with /soc@0/system-controller@4ac10000/dpi/ports/port@0/endpoint
  214. [    0.360509] platform 4ae30000.lcd-controller: Fixed dependency cycle(s) with /soc@0/dsi@4ae10000/ports/port@0/endpoint
  215. [    0.373871] platform panel: Fixed dependency cycle(s) with /soc@0/system-controller@4ac10000/dpi/ports/port@1/endpoint
  216. [    0.384636] KASLR disabled due to lack of seed
  217. [    0.414059] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages
  218. [    0.420600] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page
  219. [    0.426831] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages
  220. [    0.433586] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page
  221. [    0.439830] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages
  222. [    0.446585] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page
  223. [    0.452826] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages
  224. [    0.459585] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page
  225. [    0.467377] ACPI: Interpreter disabled.
  226. [    0.472883] iommu: Default domain type: Translated
  227. [    0.477497] iommu: DMA domain TLB invalidation policy: strict mode
  228. [    0.483962] SCSI subsystem initialized
  229. [    0.487788] usbcore: registered new interface driver usbfs
  230. [    0.493045] usbcore: registered new interface driver hub
  231. [    0.498310] usbcore: registered new device driver usb
  232. [    0.504101] mc: Linux media interface: v0.10
  233. [    0.508140] videodev: Linux video capture interface: v2.00
  234. [    0.513610] pps_core: LinuxPPS API ver. 1 registered
  235. [    0.518504] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  236. [    0.527608] PTP clock support registered
  237. [    0.531598] EDAC MC: Ver: 3.0.0
  238. [    0.535629] FPGA manager framework
  239. [    0.538828] Advanced Linux Sound Architecture Driver Initialized.
  240. [    0.545346] Bluetooth: Core ver 2.22
  241. [    0.548683] NET: Registered PF_BLUETOOTH protocol family
  242. [    0.553958] Bluetooth: HCI device and connection manager initialized
  243. [    0.560280] Bluetooth: HCI socket layer initialized
  244. [    0.565131] Bluetooth: L2CAP socket layer initialized
  245. [    0.570162] Bluetooth: SCO socket layer initialized
  246. [    0.575314] vgaarb: loaded
  247. [    0.578230] clocksource: Switched to clocksource arch_sys_counter
  248. [    0.584262] VFS: Disk quotas dquot_6.6.0
  249. [    0.588002] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
  250. [    0.594930] pnp: PnP ACPI: disabled
  251. [    0.602989] NET: Registered PF_INET protocol family
  252. [    0.607746] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
  253. [    0.615686] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
  254. [    0.623828] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
  255. [    0.631494] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
  256. [    0.639236] TCP bind hash table entries: 8192 (order: 6, 262144 bytes, linear)
  257. [    0.646632] TCP: Hash tables configured (established 8192 bind 8192)
  258. [    0.652832] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
  259. [    0.659323] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
  260. [    0.666445] NET: Registered PF_UNIX/PF_LOCAL protocol family
  261. [    0.672328] RPC: Registered named UNIX socket transport module.
  262. [    0.677995] RPC: Registered udp transport module.
  263. [    0.682659] RPC: Registered tcp transport module.
  264. [    0.687338] RPC: Registered tcp NFSv4.1 backchannel transport module.
  265. [    0.694312] PCI: CLS 0 bytes, default 64
  266. [    0.698530] hw perfevents: enabled with armv8_cortex_a55 PMU driver, 7 counters available
  267. [    0.706953] kvm [1]: IPA Size Limit: 40 bits
  268. [    0.710980] kvm [1]: GICv3: no GICV resource entry
  269. [    0.715731] kvm [1]: disabling GICv2 emulation
  270. [    0.720161] kvm [1]: GIC system register CPU interface enabled
  271. [    0.726000] kvm [1]: vgic interrupt IRQ9
  272. [    0.729905] kvm [1]: VHE mode initialized successfully
  273. [    0.735875] Initialise system trusted keyrings
  274. [    0.740253] workingset: timestamp_bits=42 max_order=18 bucket_order=0
  275. [    0.750432] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  276. [    0.756485] NFS: Registering the id_resolver key type
  277. [    0.761312] Key type id_resolver registered
  278. [    0.765436] Key type id_legacy registered
  279. [    0.769470] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
  280. [    0.776099] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
  281. [    0.783474] jffs2: version 2.2. (NAND) ? 2001-2006 Red Hat, Inc.
  282. [    0.789781] 9p: Installing v9fs 9p2000 file system support
  283. [    0.820651] Key type asymmetric registered
  284. [    0.824483] Asymmetric key parser 'x509' registered
  285. [    0.829374] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
  286. [    0.836703] io scheduler mq-deadline registered
  287. [    0.841207] io scheduler kyber registered
  288. [    0.849908] EINJ: ACPI disabled.
  289. [    0.857843] Bus freq driver module loaded
  290. [    0.866578] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
  291. [    0.874616] 44380000.serial: ttyLP0 at MMIO 0x44380010 (irq = 18, base_baud = 1500000)[    0.883977] printk: console [ttyLP0] enabled
  292. [    0.883977] printk: console [ttyLP0] enabled
  293. [    0.892386] printk: bootconsole [lpuart32] disabled
  294. [    0.892386] printk: bootconsole [lpuart32] disabled
  295. [    0.908698] cacheinfo: Unable to detect cache hierarchy for CPU 0
  296. [    0.918340] loop: module loaded
  297. [    0.922565] of_reserved_mem_lookup() returned NULL
  298. [    0.927485] megasas: 07.719.03.00-rc1
  299. [    0.936510] tun: Universal TUN/TAP device driver, 1.6
  300. [    0.941789] CAN device driver interface
  301. [    0.947309] thunder_xcv, ver 1.0
  302. [    0.950579] thunder_bgx, ver 1.0
  303. [    0.953822] nicpf, ver 1.0
  304. [    0.957321] pps pps0: new PPS source ptp0
  305. [    0.963661] fec 42890000.ethernet eth0: registered PHC device 0
  306. [    0.971553] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version
  307. [    0.978785] hns3: Copyright (c) 2017 Huawei Corporation.
  308. [    0.984157] hclge is initializing
  309. [    0.987482] e1000: Intel(R) PRO/1000 Network Driver
  310. [    0.992359] e1000: Copyright (c) 1999-2006 Intel Corporation.
  311. [    0.998145] e1000e: Intel(R) PRO/1000 Network Driver
  312. [    1.003101] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
  313. [    1.009040] igb: Intel(R) Gigabit Ethernet Network Driver
  314. [    1.014449] igb: Copyright (c) 2007-2014 Intel Corporation.
  315. [    1.020062] igbvf: Intel(R) Gigabit Virtual Function Network Driver
  316. [    1.026336] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
  317. [    1.032466] sky2: driver version 1.30
  318. [    1.036694] PPP generic driver version 2.4.2
  319. [    1.041102] PPP BSD Compression module registered
  320. [    1.045813] PPP Deflate Compression module registered
  321. [    1.051042] PPP MPPE Compression module registered
  322. [    1.055838] NET: Registered PF_PPPOX protocol family
  323. [    1.060890] usbcore: registered new interface driver rndis_wlan
  324. [    1.066839] usbcore: registered new interface driver catc
  325. [    1.072246] usbcore: registered new interface driver kaweth
  326. [    1.077824] usbcore: registered new interface driver r8152
  327. [    1.083326] usbcore: registered new interface driver cdc_ether
  328. [    1.089169] usbcore: registered new interface driver cdc_eem
  329. [    1.094837] usbcore: registered new interface driver net1080
  330. [    1.100510] usbcore: registered new interface driver rndis_host
  331. [    1.106436] usbcore: registered new interface driver cdc_subset
  332. [    1.112367] usbcore: registered new interface driver zaurus
  333. [    1.117960] usbcore: registered new interface driver sierra_net
  334. [    1.123896] usbcore: registered new interface driver cdc_ncm
  335. [    1.129565] usbcore: registered new interface driver qmi_wwan
  336. [    1.135321] usbcore: registered new interface driver cdc_mbim
  337. [    1.141077] usbcore: registered new interface driver r8153_ecm
  338. [    1.147133] VFIO - User Level meta-driver version: 0.3
  339. [    1.155111] usbcore: registered new interface driver cdc_wdm
  340. [    1.160993] usbcore: registered new interface driver uas
  341. [    1.166354] usbcore: registered new interface driver usb-storage
  342. [    1.172415] usbcore: registered new interface driver usbserial_generic
  343. [    1.178942] usbserial: USB Serial support registered for generic
  344. [    1.184954] usbcore: registered new interface driver ftdi_sio
  345. [    1.190699] usbserial: USB Serial support registered for FTDI USB Serial Device
  346. [    1.198013] usbcore: registered new interface driver option
  347. [    1.203586] usbserial: USB Serial support registered for GSM modem (1-port)
  348. [    1.210561] usbcore: registered new interface driver usb_serial_simple
  349. [    1.217089] usbserial: USB Serial support registered for carelink
  350. [    1.223180] usbserial: USB Serial support registered for flashloader
  351. [    1.229538] usbserial: USB Serial support registered for funsoft
  352. [    1.235544] usbserial: USB Serial support registered for google
  353. [    1.241459] usbserial: USB Serial support registered for hp4x
  354. [    1.247204] usbserial: USB Serial support registered for kaufmann
  355. [    1.253296] usbserial: USB Serial support registered for libtransistor
  356. [    1.259823] usbserial: USB Serial support registered for moto_modem
  357. [    1.266089] usbserial: USB Serial support registered for motorola_tetra
  358. [    1.272703] usbserial: USB Serial support registered for nokia
  359. [    1.278540] usbserial: USB Serial support registered for novatel_gps
  360. [    1.284891] usbserial: USB Serial support registered for siemens_mpi
  361. [    1.291245] usbserial: USB Serial support registered for suunto
  362. [    1.297159] usbserial: USB Serial support registered for vivopay
  363. [    1.303169] usbserial: USB Serial support registered for zio
  364. [    1.308842] usbcore: registered new interface driver usb_ehset_test
  365. [    1.317522] bbnsm_pwrkey 44440000.bbnsm:pwrkey: KEY_POWER without setting in dts
  366. [    1.325736] input: 44440000.bbnsm:pwrkey as /devices/platform/soc@0/44000000.bus/44440000.bbnsm/44440000.bbnsm:pwrkey/input/input0
  367. [    1.340443] bbnsm_rtc 44440000.bbnsm:rtc: registered as rtc0
  368. [    1.346498] bbnsm_rtc 44440000.bbnsm:rtc: setting system clock to 1970-01-01T00:00:00 UTC (0)
  369. [    1.355777] i2c_dev: i2c /dev entries driver
  370. [    1.363071] imx7ulp-wdt 42490000.wdog: imx93 wdt probe
  371. [    1.393788] Bluetooth: HCI UART driver ver 2.3
  372. [    1.398249] Bluetooth: HCI UART protocol H4 registered
  373. [    1.403378] Bluetooth: HCI UART protocol BCSP registered
  374. [    1.408696] Bluetooth: HCI UART protocol LL registered
  375. [    1.413822] Bluetooth: HCI UART protocol ATH3K registered
  376. [    1.419229] Bluetooth: HCI UART protocol Three-wire (H5) registered
  377. [    1.425619] Bluetooth: HCI UART protocol Broadcom registered
  378. [    1.431284] Bluetooth: HCI UART protocol QCA registered
  379. [    1.437888] sdhci: Secure Digital Host Controller Interface driver
  380. [    1.444095] sdhci: Copyright(c) Pierre Ossman
  381. [    1.448952] Synopsys Designware Multimedia Card Interface Driver
  382. [    1.455383] sdhci-pltfm: SDHCI platform and OF driver helper
  383. [    1.462525] ledtrig-cpu: registered to indicate activity on CPUs
  384. [    1.469682] fsl-ele-mu soc@0:ele-mu: ele_mu_probe: Not able to read cmd_tag
  385. [    1.476671] fsl-ele-mu soc@0:ele-mu: ele_mu_probe: Not able to read rsp_tag
  386. [    1.484074] fsl-ele-mu soc@0:ele-mu: assigned reserved memory node ele-reserved@a4120000
  387. [    1.492269] fsl-ele-mu soc@0:ele-mu: registering ele-trng
  388. [    1.493327] mmc0: SDHCI controller on 42850000.mmc [42850000.mmc] using ADMA
  389. [    1.497903] fsl-ele-mu soc@0:ele-mu: Successfully registered ele-trng
  390. [    1.511257] random: crng init done
  391. [    1.511363] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
  392. [    1.521284] usbcore: registered new interface driver usbhid
  393. [    1.526857] usbhid: USB HID core driver
  394. [    1.531988] mxc-md 42800000.bus:camera: deferring cap_device registration
  395. [    1.539384] usbcore: registered new interface driver rtl8733bu
  396. [    1.584557]  cs_system_cfg: CoreSight Configuration manager initialised
  397. [    1.592610] optee: probing for conduit method.
  398. [    1.597146] optee: revision 4.0 (a303fc80)
  399. [    1.597667] optee: dynamic shared memory is enabled
  400. [    1.606947] optee: initialized driver
  401. [    1.614530] mmc0: new HS400 Enhanced strobe MMC card at address 0001
  402. [    1.616893] imx93-pinctrl 443c0000.pinctrl: pin IMX93_IOMUXC_GPIO_IO26 already requested by 4ac10000.system-controller:dpi; cannot claim for 42660000.sai
  403. [    1.621467] mmcblk0: mmc0:0001 8GUF4R 7.28 GiB
  404. [    1.634628] imx93-pinctrl 443c0000.pinctrl: pin-30 (42660000.sai) status -22
  405. [    1.634635] imx93-pinctrl 443c0000.pinctrl: could not request pin 30 (IMX93_IOMUXC_GPIO_IO26) from group sai3grp  on device 443c0000.pinctrl
  406. [    1.634640] fsl-sai 42660000.sai: Error applying setting, reverse things back
  407. [    1.635512] NET: Registered PF_LLC protocol family
  408. [    1.670948]  mmcblk0: p1 p2
  409. [    1.674364] NET: Registered PF_INET6 protocol family
  410. [    1.674372] mmcblk0boot0: mmc0:0001 8GUF4R 31.9 MiB
  411. [    1.675467] mmcblk0boot1: mmc0:0001 8GUF4R 31.9 MiB
  412. [    1.680139] Segment Routing with IPv6
  413. [    1.685236] mmcblk0rpmb: mmc0:0001 8GUF4R 4.00 MiB, chardev (234:0)
  414. [    1.689367] In-situ OAM (IOAM) with IPv6
  415. [    1.703196] NET: Registered PF_PACKET protocol family
  416. [    1.708270] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
  417. [    1.721204] can: controller area network core
  418. [    1.725587] NET: Registered PF_CAN protocol family
  419. [    1.730378] can: raw protocol
  420. [    1.733334] can: broadcast manager protocol
  421. [    1.737509] can: netlink gateway - max_hops=1
  422. [    1.742111] Bluetooth: RFCOMM TTY layer initialized
  423. [    1.747003] Bluetooth: RFCOMM socket layer initialized
  424. [    1.752150] Bluetooth: RFCOMM ver 1.11
  425. [    1.755941] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
  426. [    1.761243] Bluetooth: BNEP filters: protocol multicast
  427. [    1.766463] Bluetooth: BNEP socket layer initialized
  428. [    1.771417] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
  429. [    1.777330] Bluetooth: HIDP socket layer initialized
  430. [    1.782496] 8021q: 802.1Q VLAN Support v1.8
  431. [    1.786704] lib80211: common routines for IEEE802.11 drivers
  432. [    1.792458] 9pnet: Installing 9P2000 support
  433. [    1.796809] Key type dns_resolver registered
  434. [    1.801431] registered taskstats version 1
  435. [    1.805541] Loading compiled-in X.509 certificates
  436. [    1.824942] usb_phy_generic soc@0:usbphynop1: supply vcc not found, using dummy regulator
  437. [    1.833727] usb_phy_generic soc@0:usbphynop1: dummy supplies not allowed for exclusive requests
  438. [    1.842593] usb_phy_generic soc@0:usbphynop2: supply vcc not found, using dummy regulator
  439. [    1.850857] usb_phy_generic soc@0:usbphynop2: dummy supplies not allowed for exclusive requests
  440. [    1.871755] imx-dwmac 428a0000.ethernet: IRQ eth_lpi not found
  441. [    1.878022] imx-dwmac 428a0000.ethernet: User ID: 0x10, Synopsys ID: 0x52
  442. [    1.884823] imx-dwmac 428a0000.ethernet:     DWMAC4/5
  443. [    1.889606] imx-dwmac 428a0000.ethernet: DMA HW capability register supported
  444. [    1.896732] imx-dwmac 428a0000.ethernet: RX Checksum Offload Engine supported
  445. [    1.903856] imx-dwmac 428a0000.ethernet: TX Checksum insertion supported
  446. [    1.910543] imx-dwmac 428a0000.ethernet: Wake-Up On Lan supported
  447. [    1.916681] imx-dwmac 428a0000.ethernet: Enable RX Mitigation via HW Watchdog Timer
  448. [    1.924325] imx-dwmac 428a0000.ethernet: Enabled L3L4 Flow TC (entries=8)
  449. [    1.931102] imx-dwmac 428a0000.ethernet: Enabled RFS Flow TC (entries=10)
  450. [    1.937885] imx-dwmac 428a0000.ethernet: Enabling HW TC (entries=256, max_off=256)
  451. [    1.945445] imx-dwmac 428a0000.ethernet: Using 32/32 bits DMA host/device width
  452. [    1.958883] ci_hdrc ci_hdrc.0: EHCI Host Controller
  453. [    1.963790] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
  454. [    1.986238] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
  455. [    1.992125] hub 1-0:1.0: USB hub found
  456. [    1.995900] hub 1-0:1.0: 1 port detected
  457. [    2.003775] isi-capture 4ae40000.isi:cap_device: deferring 4ae40000.isi:cap_device device registration
  458. [    2.013225] mxc-isi 4ae40000.isi: mxc_isi.0 registered successfully
  459. [    2.020279] mxc-md 42800000.bus:camera: deferring cap_device registration
  460. [    2.028914] remoteproc remoteproc0: imx-rproc is available
  461. [    2.038767] regulator-panel_powr1 GPIO handle specifies active low - ignored
  462. [    2.045853] reg-fixed-voltage regulator-panel_powr1: nonexclusive access to GPIO for regulator-panel_powr1
  463. [    2.056757] i2c 0-003c: Fixed dependency cycle(s) with /soc@0/bus@42800000/camera/csi@4ae00000/port@0/endpoint
  464. [    2.067185] ov5640 0-003c: supply DOVDD not found, using dummy regulator
  465. [    2.073997] ov5640 0-003c: supply AVDD not found, using dummy regulator
  466. [    2.080627] ov5640 0-003c: supply DVDD not found, using dummy regulator
  467. [    2.124536] ov5640 0-003c: ov5640_read_reg: error: reg=300a
  468. [    2.130130] ov5640 0-003c: ov5640_check_chip_id: failed to read chip identifier
  469. [    2.137619] ov5640: probe of 0-003c failed with error -5
  470. [    2.143943] sgtl5000 0-000a: sgtl5000 revision 0x11
  471. [    2.154090] at24 0-0050: supply vcc not found, using dummy regulator
  472. [    2.160772] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write
  473. [    2.168379] rtc-rx8025t 0-0032: registered as rtc1
  474. [    2.173674] ptn5150 0-003d: No VBUS GPIO, ignoring VBUS control
  475. [    2.180256] OF: graph: no port node found in /soc@0/bus@44000000/i2c@44340000/typec@3d
  476. [    2.188387] i2c i2c-0: LPI2C adapter registered
  477. [    2.194024] i2c 1-0039: Fixed dependency cycle(s) with /soc@0/dsi@4ae10000/ports/port@1/endpoint
  478. [    2.203188] myir i2c_gpio probe
  479. [    2.206336] at9555 gpio_base=130
  480. [    2.210524] at9555_gpio 1-0020: probed
  481. [    2.214430] nxp-pca9450 1-0025: No IRQ configured?
  482. [    2.219221] nxp-pca9450: probe of 1-0025 failed with error -22
  483. [    2.225425] i2c i2c-1: LPI2C adapter registered
  484. [    2.225622] edt_ft5x06 1-0038: supply vcc not found, using dummy regulator
  485. [    2.231308] imx-drm display-subsystem: bound imx-lcdifv3-crtc.0 (ops lcdifv3_crtc_ops)
  486. [    2.236944] edt_ft5x06 1-0038: supply iovcc not found, using dummy regulator
  487. [    2.244783] [drm:drm_bridge_attach] *ERROR* failed to attach bridge /soc@0/dsi@4ae10000 to encoder DSI-34: -517
  488. [    2.261863] dw-mipi-dsi-imx 4ae10000.dsi: [drm:dw_mipi_dsi_imx_bind] *ERROR* failed to attach bridge: -517
  489. [    2.262245] usb 1-1: new high-speed USB device number 2 using ci_hdrc
  490. [    2.271738] dw-mipi-dsi-imx 4ae10000.dsi: [drm:dw_mipi_dsi_imx_probe] *ERROR* failed to register component: -517
  491. [    2.296578] sdhci-esdhc-imx 42860000.mmc: Got CD GPIO
  492. [    2.297093] mx8-img-md: Registered mxc_isi.0.capture as /dev/video0
  493. [    2.307982] mxc-md 42800000.bus:camera: deferring csi device registration
  494. [    2.315908] dwc-mipi-csi2-host 4ae00000.csi: lanes: 2, name: mxc-mipi-csi2.0
  495. [    2.329043] regulator-panel GPIO handle specifies active low - ignored
  496. [    2.330454] mmc1: SDHCI controller on 42860000.mmc [42860000.mmc] using ADMA
  497. [    2.335932] debugfs: Directory 'panel-power1' with parent 'regulator' already present!
  498. [    2.443394] hub 1-1:1.0: USB hub found
  499. [    2.447290] hub 1-1:1.0: 4 ports detected
  500. [    2.550831] lt9611 1-0039: LT9611 revision: 0xe2
  501. [    2.561183] imx-drm display-subsystem: bound imx-lcdifv3-crtc.0 (ops lcdifv3_crtc_ops)
  502. [    2.569320] imx-drm display-subsystem: bound 4ae10000.dsi (ops dw_mipi_dsi_imx_ops)
  503. [    2.577099] imx-drm display-subsystem: bound 4ac10000.system-controller:dpi (ops imx93_pdf_ops)
  504. [    2.578623] input: generic ft5x06 (79) as /devices/platform/soc@0/44000000.bus/44350000.i2c/i2c-1/1-0038/input/input1
  505. [    2.586163] [drm] Initialized imx-drm 1.0.0 20120507 for display-subsystem on minor 0
  506. [    2.605483] imx-drm display-subsystem: [drm] fb0: imx-drmdrmfb frame buffer device
  507. [    2.614823] mx8-img-md: Registered mxc_isi.0.capture as /dev/video0
  508. [    2.621267] unregister ISI channel: mxc_isi.0
  509. [    2.626773] input: gpio-keys as /devices/platform/gpio-keys/input/input2
  510. [    2.634189] cfg80211: Loading compiled-in X.509 certificates for regulatory database
  511. [    2.643321] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
  512. [    2.649958] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
  513. [    2.654999] ALSA device list:
  514. [    2.658584] platform regulatory.0: Falling back to sysfs fallback for: regulatory.db
  515. [    2.661601]   #0: SGTL5000-Card
  516. [    2.673104] /dev/root: Can't open blockdev
  517. [    2.677240] VFS: Cannot open root device "mmcblk0p3" or unknown-block(179,3): error -6
  518. [    2.685165] Please append a correct "root=" boot option; here are the available partitions:
  519. [    2.693640] b300         7634944 mmcblk0
  520. [    2.693645]  driver: mmcblk
  521. [    2.700451]   b301          512000 mmcblk0p1 d514cfe4-01
  522. [    2.700456]
  523. [    2.707248]   b302         7020544 mmcblk0p2 d514cfe4-02
  524. [    2.707252]
  525. [    2.714058] b320           32640 mmcblk0boot0
  526. [    2.714062]  (driver?)
  527. [    2.720846] b340           32640 mmcblk0boot1
  528. [    2.720849]  (driver?)
  529. [    2.727638] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,3)
  530. [    2.736060] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.1.55+ga5c552ce6210 #1
  531. [    2.743182] Hardware name: NXP i.MX93 11X11 EVK board (DT)
  532. [    2.748651] Call trace:
  533. [    2.751086]  dump_backtrace.part.0+0xe0/0xf0
  534. [    2.755358]  show_stack+0x18/0x30
  535. [    2.758669]  dump_stack_lvl+0x64/0x80
  536. [    2.762326]  dump_stack+0x18/0x34
  537. [    2.765628]  panic+0x18c/0x344
  538. [    2.768670]  mount_block_root+0x188/0x238
  539. [    2.772674]  mount_root+0x20c/0x24c
  540. [    2.776149]  prepare_namespace+0x130/0x170
  541. [    2.780231]  kernel_init_freeable+0x258/0x284
  542. [    2.784573]  kernel_init+0x24/0x12c
  543. [    2.788048]  ret_from_fork+0x10/0x20
  544. [    2.791612] SMP: stopping secondary CPUs
  545. [    2.795524] Kernel Offset: disabled
  546. [    2.799003] CPU features: 0x60000,000400a4,6600721b
  547. [    2.803865] Memory Limit: none
  548. [    2.806912] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,3) ]---

复制代码
重新下载了好几次也不行。
收藏 转播 分享 顶 踩
分享到：
回复

使用道具 举报

返回列表
高级模式
B Color Image Link Quote Code Smilies
您需要登录后才可以回帖 注册/登录

本版积分规则

avatar
8788 积分
42 主题
+ 关注
关闭

站长推荐上一条 /3 下一条

  • 手机版| 小黑屋|

? 2010 - 2025 苏州广东会网络科技有限公司 版权所有 ICP经营许可证 苏B2-20140176 | 苏ICP备14012660号-6 | 苏公网安备 32059002001874号